n0613hk 20131023-s00001 no.a2242-1/4 semiconductor components industries, llc, 2013 november, 2013 http://onsemi.com LC898212XD overview this lsi is af control lsi. it consists of 1 system of feed back circuit for af control. features ? built-in equalizer circuit using digital operation - af control equalize circuit - any coefficient can be specified by i 2 c i/f ? i 2 c interface ? built-in a/d converter - maximum 10-bit - input 2 channel ? built-in d/a converter - 8-bit - output 2-channel (hall offset, constant current bias) ? built-in op amp - 1 channel - hall amp ? built-in osc - 48mhz (frequency adjustment function) ? built-in pwm pulse generator circuit - pwm circuit for af control ? 1-chip motor driver - saturation drive h bridge 1 channel ? package - wl-csp 12-pin - lead-free, halogen-free ? supply voltage - logic unit : internal core typ 1.2v, avdd (2.6v to 3.6v) - driver unit : vm (2.6v to 3.6v) orderin g numbe r : ena2242 cmos lsi af controller ordering information see detailed ordering and shipping inform ation on page 4 of this data sheet. * i 2 c bus is a trademark of philips corporation. wlp12j(1.77x1.37)
LC898212XD no.a2242-2/4 pin description type i input p power supply, gnd nc not connect o output b bidirection i 2 c interface i2cck b i 2 c clock pin i2cdt b i 2 c data pin d/a interface biaso o d/a output (hall bias input) op-amp interface opinp i op-amp input opinm i op-amp input driver interface out1 o actuator output pin out2 o actuator output pin power supply pin vdd p digital power supply vss p digital gnd vddo p ldo power supply out vm p motor power supply pgnd p power gnd pin type ?o? ? ensure that it is set to open. pin type ?i? ? open is inhibited. en sure that it is connected to the v dd or v ss even when it is unused. (please contact our company for more information about selection of v dd or v ss .) pin type ?b? ? if you are unsure about processing method on the pin description of pin layout table, please contact us. note that incorrect processing of unused pins may result in defects. if you have any question, please feel free to contact us.
LC898212XD no.a2242-3/4 pin layout circuit name number of pins circuit name number of pins analog 4 driver 4 logic 4 backside pin layout diagram (top view from the mold side) 4 vddo vm pgnd 3 avdd i2cdt out1 2 opinp i2cck out2 1 vss opinm biaso a b c block diagram - + - + - +
LC898212XD ps no.a2242-4/4 package dimensions wlp12j(1.77x1.37) unit : mm ordering information device package shipping (qty / packing) LC898212XD-sh wlp12j(1.77x1.37) (pb-free / halogen free) 5000 / tape & reel on semiconductor and the on logo are registered trademarks of semiconductor components industries, llc (scillc). scillc owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. a listing of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent-marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc mak es no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability ar ising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequentia l or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s techn ical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorize d for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other appli cation in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of persona l injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture o fthe part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws a nd is not for resale in any manner. wlcsp12, 1.77x1.37 case 567gh issue o seating plane 0.10 c notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. coplanarity applies to the spherical crowns of the solder balls. 2x dim a min max ??? millimeters a1 d 1.77 bsc e b 0.15 0.25 e 0.40 bsc 0.33 d e a b pin a1 reference e a 0.05 b c 0.03 c 0.08 c 12x b 4 c b a 0.13 c a1 a2 c 0.03 0.13 1.37 bsc 0.25 12x dimensions: millimeters *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* 0.40 0.10 c 2x top view side view bottom view note 3 a2 0.20 ref recommended a1 package outline 123 pitch 0.40 pitch a e/2 e
|
